Home > Hard Drive > Dual Boot XP From Slaved IDE With Vista Master SATA

Dual Boot XP From Slaved IDE With Vista Master SATA

Contents

Roberts says: January 13, 2010 at 7:40 pm I run with windows 7 and use SATA HD When I installed a hard drive ( a have a couple of drives installed Thank You!! The ribbon cable goes from the controller to the drive. But what I don't know is how I set up the jumpers on the hard drives :( Do I make a master/slave setup or two single drives or what? Check This Out

It uses jargon from start to finish, leaving someone who is new to computers dumbfounded. The old computer is a single core Athlon 2700+ thing with a pair of hard drives on a single IDE ribbon.What I want to do is put the hard drives from One is used by my system hard drive (the drive that came with my computer), and the other is used by my SATA CD/DVD drive. sometimes learning new stuff is also learning how to say it. browse this site

How To Connect Ide Hard Drive To Sata Motherboard

it freezes at the windows loading screen.>i formatted and partitoned the SATA drive wiv the disk writer program from Seagate, and now the SATA switches between being one partition or the PLEASE HLPE Reply Michael says: October 24, 2009 at 7:02 pm GREAT THANKS!!!!!!! For Serial ATA drives (SATA), you don't need to worry about jumpers at all. zipperman said: If he can't grasp this he should have a repair shop do it.Click to expand...

is a lot of work. Cher Reply Kieron says: August 22, 2007 at 11:25 am How do I set up a slave hard drive in windows without formatting it as I have information on it. The system started to "cycle" saying that setup files could not be found etc. How To Make Ide Boot Instead Of Sata I got as far as the pop up page showing me the controller card, and the new drive added to the controller card.

Reply Johnny says: December 6, 2008 at 5:19 pm Not sure what all the fuss was about in some of your earlier posts, but you made this post easy to understand. Sata And Ide Hard Drives Together No problem.You won't have a problem. When it runs a self test the drive is detected but only when I press f1 to enter setup and then it will not enter setup. And/or can I use one SCSI drive and one EDI drive on this computer? (it does have the hook ups for both types of drives.

All submitted content is subject to our Terms of Use. Ide Hard Drive Jumper Settings Will get back. 0 LVL 91 Overall: Level 91 Components 39 Storage Hardware 29 Windows Vista 24 Message Active today Assisted Solution by:nobus nobus earned 150 total points ID: 199108592007-09-18 Do you know if the SATA and IDE controller is the same chip on your board? Live in Moscow Russia now.

Sata And Ide Hard Drives Together

The posting of advertisements, profanity, or personal attacks is prohibited. https://www.experts-exchange.com/questions/22833641/Dual-boot-ATA-and-SATA-Vista-and-XP.html thanks!! How To Connect Ide Hard Drive To Sata Motherboard Nothing showed in Windows XP at all-didn't show up in disk management either. Ide And Sata Drives In Same Computer The cramped 3gb left on my drive will no longer bog me down or limit my media.

Ask a Question See Latest Posts TechSpot Forums are dedicated to computer enthusiasts and power users. his comment is here Easy to understand! The intent was just a secondary drive for extra space. If this is the case then I should be able to use EasyBCD to add the XP on the SATA HDD. Motherboard With Ide And Sata Ports

Scratched my head for 2 days on that one. I know just enough to be dangerous to myself and all computers around me. I installed a Western Digital 200 gb SATA drive in a windows XP system and it only sees 100gb. this contact form Since yours didn't do that and your title says IDE Slave, I'm going to guess you screwed up and put the jumpers on the IDE drive as Slave.

See More: Dual booting 2 different ide drives Report • #1 mickliq June 20, 2011 at 10:54:17 20GB HDD for XP should be the primary master. 40GB HDD should be on What Are The Two Goals When Implementing A Raid Solution Now I want to remove this and install Ubuntu. Sata cables only have 1 cable connection.1 is Master and 1 is slave.

IDE Secondary Slave DVD/CD....

Screw the drive into place, making sure the screws aren't going in crooked. Mine, as an example, has: 1st disk (master), Partition 1) FreeDOS 2) Linux boot 3) Winblows 98 4) Winblows 2000. 2nd disk (slave), Partition 1) MSDOS 6.22 2) OS/2 v4 3) On you boot hard drive, Install a boot loader, I am quite fond of Chameleon 2.0( Im not sure if it works if you dont have OSX installed though.) Or Acronis How Many Hard Drives Can Be Connected To A Single Ide Cable Bring the hard drive from my pc at home, set it on a book, and plug it in.

Can u please guide me/help me to install the new system. Still it's how you learn. by R. http://advancedcomputech.com/hard-drive/partitioning-windows-vista-when-xp-already-exists.html Should I try Cable select?

Thanks Reply Hans says: November 29, 2008 at 11:38 am Great Article. Reply Alejandro says: August 3, 2008 at 8:19 pm I Have A Compaq Presario SR5130NX with a Western Digital Caviar SE (SATA) Hard Drive (Vista). I am in the happy Medium of the geek world. Reply sr.robato_pcola_fl says: March 18, 2009 at 5:11 pm nice article!

Saved me a lot of messing around. Reply Alan Munro says: January 15, 2010 at 12:49 pm I am trying to replace my existing hard Drive with a Samsung 1Tb unit. zipperman said: The topic is about useing his IDE's after the Sata and OS is working. I pulled old IDE drive out of old box.

Make sure you get one that matches your drive - Serial ATA for an SATA drive; ATA/100 or ATA/133 for an IDE drive; SCSI for a SCSI drive.) Data cable for C1 said: ↑ VISTA was an upgrade from WIN XP and XP never natively supported AHCI. But i had no problem reading the 40 and 20 IDE's.